RAPIDTAC FLUIDS
RAPIDREMOVER ADHESIVE REMOVER (PALE LEMON COLOUR)
Quick and easy way to remove old adhesive residue without damage. It works quickly, normally under a minute, will not leave an oily residue and is water-soluble.
Stage One: Remove the old graphic with a heat gun.
Stage Two: Spray RAPIDREMOVER onto the adhesive residue and allow it to penetrate for 30 - 60 seconds.
Stage Three: Use a squeegee to scrape and remove the softened adhesive.
Stage Four: Spray RAPIDREMOVER onto a rag or paper towel and wipe the area clean. Rinse surface thoroughly with RAPIDPREP, in preparation for the new graphic. Use in a well ventilated area. Due to the varying condition of paintwork and substrates, apply to a test area first. Refer to our data sheets for further information.
Available sizes: 4oz, 32oz and 1 US gallon
Also available: RAPIDREMOVER Spray bottle - 30oz (887ml) with spray nozzle
RAPIDPREP CLEANING FLUID (ORANGE COLOUR)
The quick and easy way to clean and degrease, in preparation for vinyl graphics. RAPIDPREP will clean and degrease the surface properly. It will only leave compatible residues and will ensure wax, silicone and oils are not left on the surface. It is non-flammable and non-hazardous.
Stage One: Shake the bottle of RAPIDPREP well and spray onto the surface, ideally 1M diameter at a time.
Stage Two: Wait 30 seconds, then wipe clean with a paper towel (do not use a commercial kitchen towel or cloth rag).
Stage Three: Repeat stages 1 and 2 until the area is clean.
Available sizes: 4oz, 32oz, 1 US gallon and 4 US gallon pack
Also available: RAPIDPREP Spray bottle - 32oz (946ml) empty bottle with spray nozzle
RAPIDTAC ORIGINAL APPLICATION FLUID (FLESH PINK COLOUR) AND RAPIDTAC II APPLICATION FLUID (DARK GREEN COLOUR)
The quick and easy way to apply vinyl graphics wet. Compared with soapy water, RAPIDTAC can significantly improve the adhesive bond. Independent laboratory tests show 300% improvement in adhesion after 6 hours and 50% after 24 hours, with the final adhesion values over 10% higher. This increase in adhesion values, shortly after application, allows application tapes to be removed very quickly, resulting in shorter field visits. RAPIDTAC speeds up application times, eliminates bubbling and wrinkling, helps application in cold and hot weather and makes the final result look consistently professional, especially on glass. RAPIDTAC II is the latest addition to the range and works twice as quickly as the original, as well as now working down to 0°C.
Stage One: Shake the bottle of RAPIDTAC well and using strips of masking tape, position the graphic image.
Stage Two: Lift the image and use RAPIDTAC sparingly to spray the substrate. Remove the liner from the film and place the self-adhesive image on the wet surface.
Stage Three: Finalise the position of the decal. Squeegee out the excess liquid, working from the centre outwards in all directions to enable the adhesive to start bonding. Wait 2 - 3 minutes.
Stage Four: Spray the RAPIDTAC fluid directly onto the application tape, then remove the tape slowly, pulling diagonally. Wipe over the surface with a paper towel.
Available sizes: 4oz, 32oz, 1 US gallon and 4 US gallon pack
Also available: RAPIDTAC Spray bottle - 32oz (946ml) empty bottle with spray nozzle
RAPIDCLEAR SHEET AND GLASS POLISH (PALE BLUE COLOUR)
The perfect way to finish work on acrylic, glass and polycarbonate. RAPIDCLEAR will leave a luster to your work that is sure to impress. RAPIDCLEAR is non-hazardous, non-flammable and bio-degradable.
Due to the silicone content in the polish, graphics must be adhered before polishing the finished panel.
Available sizes: 4oz, 32oz, 1 US gallon and 4 US gallon pack
Also available: RAPIDCLEAR Spray bottle - 32oz (946ml) empty bottle with spray nozzle